MSO72004C

Description

Specifications

All specifications are guaranteed unless noted otherwise. All specifications apply to all models unless noted otherwise.

Model overview

Vertical system – Analog channels

Bandwidth limit

Depending on instrument model: 33 GHz to 1 GHz in 1 GHz steps, or 500 MHz

Depending on instrument model, hardware-only bandwidth settings at 33, 25, 23, 20, 16, 12.5, 8, 6, and 4 GHz

Channel-to-Channel isolation

Any two channels at equal vertical scale

0 GHz to 10 GHz: ≥120:1

>10 GHz to 12 GHz: ≥80:1

>12 GHz to 15 GHz: ≥50:1

>15 GHz to 20 GHz: ≥25:1

>20 GHz to 33 GHz: ≥20:1

DC gain accuracy

±2% (of reading)

Channel delay (typical)

≤10 ps for any two channels at equal V/div and coupling on C models

≤1 ps for any two channels at equal V/div and coupling on DX models

Effective number of bits (typical)

5.5 bits at 50 mV/div, bandwidth filter on, max bandwidth up to 13 GHz, max sample rate

Signal-to-Noise ratio (typical)

34 dB

Input coupling

DC (50 Ω), GND

Input resistance selection

50 Ω ±3%, 1 MΩ with TCA-1MEG adapter

Input sensitivity range

23 GHz, 25 GHz, and 33 GHz models

6.25 mV/div to 600 mV/div (62.5 mV to 6 V full scale)

20 GHz models

20 to 500 mV/div (200 mV to 5 V full scale)

10 mV/div at 18 GHz (100 mV full scale)

All other models

10 mV/div to 500 mV/div (100 mV to 5 V full scale)

Maximum input voltage, 50 Ω

Also determined by TekConnect^® accessory.

23 GHz, 25 GHz, and 33 GHz models

≤1.2 V_FS: ±1.5 V relative to the termination bias (30 mA maximum), ±5 V absolute maximum input.

>1.2 V_FS: 8.0 V.

All other models

<5.0 V_RMS for ≥100 mV/div; 1.0 V_RMS for <100 mV/div

Termination voltage range

23 GHz, 25 GHz, and 33 GHz models

≤1.2 V_FS: -3.5 V to +3.5 V>1.2 V_FS: 0 V.

All other models

0 V only

Offset accuracy

10 mV/div to 99.5 mV/div

±(0.35% (offset value-position) + 1.5 mV + 1% of full scale)

100 mV/div to 500 mV/div

±(0.35% (offset value-position) + 7.5 mV + 1% of full scale)

Offset range

23 GHz, 25 GHz, and 33 GHz models

+3.4 V to ‒3.4 V

All other models

10 mV/div: ±450 mV

20 mV/div: ±400 mV

50 mV/div: ±250 mV

100 mV/div: ±2.0 V

200 mV/div: ±1.5 V

500 mV/div: ±0.0 V

Passband flatness (20, 50, 100, 250 mV/div) (typical)

±0.5 dB to 50% of nominal bandwidth

Position range

±5 div

Vertical resolution

8 bit (11 bit with averaging)

Vertical system – Digital channels

Digital bandwidth

With P6780 logic probe

2.5 GHz

With P6750 or P6717A logic probe

1 GHz

Input resistance selection

With P6780 logic probe

20 kΩ to ground per side or 40 kΩ differential mode ± 2.0%, 0.5 pF

With P6750 or P6717A logic probe

20 kΩ ± 1.0%, 3 pF

Trigger clock/qualifier input

1

Vertical resolution

1 bit

Thresholds

One per channel, independently set

Threshold accuracy

±75 mV + 3% of threshold setting

Threshold resolution

5 mV

Threshold voltage range

With P6780 logic probe

–2 to +4.5 V

With P6750 or P6717A logic probe

–1.5 to +4.0 V

Minimum voltage swing

300 mV_p-p

Maximum input voltage

±15 V nondestruct

Horizontal system

Channel-to-Channel deskew range

±75 ns

Time base accuracy

±1.5 ppm initial accuracy, aging <1 ppm per year

Time base delay time range

–5.0 ks to 1.0 ks

Trigger jitter

<100 fs_RMS (1 ps_RMS [typical] with enhanced triggering off)

Acquisition system – Analog channels

Acquisition modes

Sample

Acquires and displays sampled values

Average

From 2 to 10,000 waveforms can be included in an average waveform

Envelope

From 1 to 2×10⁹ waveforms included in min-max envelope

Hi-Res

Real-time boxcar averaging reduces random noise and increases resolution

Peak detect

Capture and display narrow glitches at all real-time sampling rates. Glitch widths: 1 ns at ≤125 MS/s; 1/sample rate at ≥250 MS/s

FastAcq®

FastAcq® optimizes the instrument for analysis of dynamic signals and capture of infrequent events, capturing >300,000 wfms/s on all TekConnect channels simultaneously, standalone configuration only

FastFrame™

Acquisition memory divided into segments; maximum trigger rate >310,000 waveforms per second. Time of arrival recorded with each event. Frame finder tool helps to visually identify transients. TekConnect channels only, standalone configuration only

Roll mode

Scrolls sequential waveform points across the display in a right-to-left rolling motion. Works at sample rates up to 10 MS/s with a maximum record length of 40 MS. TekConnect channels only, standalone configuration only

Waveform database

Accumulates waveform data providing a three-dimensional array of amplitude, time, and counts. TekConnect channels only, standalone configuration only

Acquisition system – Digital channels

Maximum sample rate (all channels)

12.5 GS/s

Timing resolution

80 ps

Channel-to-Channel timing uncertainty

<160 ps

Minimum detectable pulse width

<400 ps

Maximum number of buses

16

Number of channels per bus

Up to 24 (16 logic, 4 analog, 4 math)

Pinpoint® trigger system

Trigger sensitivity

Internal DC coupled

4% of full scale from DC to 50 MHz

10% of full scale at 4 GHz

20% of full scale at 8 GHz

50% of full scale at 11 GHz

Aux input 50 Ω (external trigger)

250 mV from DC to 50 MHz, increasing to 350 mV at 1.0 GHz

A event and delayed B event trigger types

Edge, glitch, width, runt, timeout, transition time, logic pattern, logic state, setup/hold, window – all except edge, pattern, and state can be logic state qualified by up to two channels

Main trigger modes

Auto, Normal, and Single

Trigger sequences

Main, Delayed by Time, Delayed by Events, Reset by Time, Reset by State, Reset by Transition. All sequences can include a separate horizontal delay after the trigger event to position the acquisition window in time

Trigger coupling

DC, AC (attenuates <100 Hz)

HF Rej (attenuates >20 kHz)

LF Rej (attenuates <200 kHz)

Noise Reject (reduces sensitivity)

RF coupling (increases trigger sensitivity and bandwidth at the highest operating frequencies)

Trigger holdoff range

250 ns min to 12 s max

Trigger level range

Any channel

±120% of full scale from center of screen

Auxiliary input

±5 V

Line

0 V, not settable

Clock recovery system

DPO Models

Requires Option ST6G or Option MTH

MSO Models

Standard

Clock recovery phase locked loop bandwidth

Fixed at FBaud/1600

Clock recovery jitter (RMS)

<0.25% bit period + 2 ps_RMSfor PRBS data patterns

<0.25% bit period + 1.5 ps_RMSfor repeating “0011” data pattern

Minimum signal amplitude needed for clock recovery

1 div_p-pup to 1.25 Gbaud

1.5 div_p-pabove 1.25 Gbaud

Tracking/Acquisition range

±2% of requested baud

Clock recovery frequency range

1.5 MBaud to 3.125 GBaud. Recovered clock and regenerated data available for use with a BERT.

Serial pattern trigger

DPO Models

Requires Option ST6G

MSO Models

Standard

NRZ-Encoded Data

Up to 64 bit serial word recognizer, bits specified in binary (high, low, don’t care) or hex format

Trigger on NRZ-encoded data up to 1.25 GBaud

8b/10b-Encoded Data

Trigger on 8b/10b-encoded data at the following rates: 1.25 to 1.65, 2.1 to 3.2, 3.8 to 5.1, and 5.4 to 6.25 GBaud.

Pattern length up to 40 bits (1 to 4 valid 10-bit characters)

Alignment character is K28.5 (either disparity)

Communications-related triggers

Support for AMI, HDB3, BnZS, CMI, MLT3, and NRZ encoded communications signals. Select among isolated positive or negative one, zero pulse form, or eye patterns as applicable to the standard.

DPO Models

Requires Option MTH

MSO Models

Standard

Bus triggers maximum toggle rate

I²C, SPI, RS-232/422/485/UART: 10 Mb/s

USB: low-speed, full-speed

CAN: 1 Mb/s

LIN: 100 kb/s

MIL-STD-1553B: 2 Mb/s

Logic pattern trigger (MSO Models)

Threshold range

P6780: –2 to +4.5 V

P6717A/P6750: –1.5 to +4 V

Threshold accuracy

±100 mV + 3% of threshold setting

Enhanced triggering

Enhanced triggering corrects the difference in timing between the trigger path and the acquired data path (supports all Pinpoint trigger types on both A- and B-Events except pattern trigger); Default On (user-selectable); Not available in FastAcq mode.

Line trigger

Trigger on power line signal. Level fixed at 0 V.

Visual Trigger

Requires Option VET

Max number of areas

8

Area shapes

Rectangle, Triangle, Trapezoid, Hexagon, user defined shapes (can have >40 vertices)

Compatibility

Visual Trigger qualification is compatible with all trigger types and all trigger sequences

Trigger Types

Trigger	Analog Channels	MSO Logic Channels	Description
Comm 1	X		Support for AMI, HDB3, BnZS, CMI, MLT3, and NRZ encoded signals.
Bus	X	X	Trigger on a parallel or serial bus when the specific bus value is found.
I2C 1	X	X	Trigger on Start, Repeated Start, Stop, Missing ACK, Address (7 or 10 bit), Data, or Address and Data.
SPI 1	X	X	Trigger on SS or data.
CAN 2	X	X	Trigger on Start of Frame, Frame Type, Identifier, Data, End of Frame, Missing Ack, Bit Stuff Error.
LIN 2	X	X	Trigger on Sync, Identifier, Data, Ident and Data, Wakeup Frame, Sleep Frame, Error.
FlexRay 2	X	X	Trigger on Start of Frame, Indicator Bits, Cycle Count, Header Fields, Identifier, Data, End of Frame, Error.
RS-232/422/485/UART 2	X	X	Trigger on Start Bit, End of Packet, Data, and Parity Error.
USB 2	X	X	Low-speed or Full-speed: Trigger on Sync, Reset, Suspend, Resume, End of Packet, Token (Address) Packet, Data Packet, Handshake Packet, Special Packet, Error.
MIL-STD-1553B2	X	X	Trigger on Sync, Command Word, Status Word, Data, RT/IMG Time, Error.
PCI Express 2	X	X	Trigger on Patterns (including ordered sets), Character/Symbol, Error, Control Characters (gen 1 and gen 2 rates only)
Edge	X	X	Positive or negative slope on any channel or front-panel auxiliary input. Coupling includes DC, AC, noise reject, HF reject, and LF reject.
B Event Scan	X		B Event Scan is an A to B trigger sequence that will trigger and capture burst event data of interest as defined in the B Event Scan setup menu. Captured bits can be scanned in a sequential or randomized fashion, and alternatively the trigger can toggle between two successive B trigger events. Eye diagrams can be constructed with burst data acquired as a result of scanning B Event.
Glitch	X	X	Trigger on or reject glitches of positive, negative, or either polarity. Minimum glitch width is 150 ps (typical) with rearm time of 300 ps.
Pattern	X	X	Trigger when pattern goes false or stays true for specified period of time. Pattern (AND, OR, NAND, NOR) specified for four input channels (and 16 logic channels on the MSO70000 Series) defined as high, low, or don’t care.
Runt	X		Trigger on a pulse that crosses one threshold but fails to cross a second threshold before crossing the first again. Event can be time- or logic-qualified.
Serial Pattern 1	X		Trigger on NRZ-encoded data up to 6.25 Gbaud; above 1.25 Gbaud requires 8b/10b encoded data. Includes pattern lock triggering to capture repeated acquisitions of long serial test patterns up to 6.25 Gb/s.
Setup/Hold	X		Trigger on violations of both setup time and hold time between clock and data present on any two input channels.
State	X	X	Any logical pattern of channels (1, 2, 3) (and 16 logic channels on the MSO70000 Series) clocked by edge on channel 4. Trigger on rising or falling clock edge.
Timeout	X	X	Trigger on an event which remains high, low, or either, for a specified time period. Selectable from 300 ps.
Transition	X		Trigger on pulse edge rates that are faster or slower than specified. Slope may be positive, negative, or either.
Trigger Delay by Events	X	X	1 to 2 billion events.
Trigger Delay by Time	X	X	3.2 ns to 3 million seconds.
Visual Trigger2	X		Trigger when the Visual Trigger expression is satisfied.
Width	X	X	Trigger on width of positive or negative pulse either within or out of selectable time limits (down to 150 ps).
Window	X		Trigger on an event that enters or exits a window defined by two user-adjustable thresholds. Event can be time or logic qualified.

¹Included on MSO models, optional on DPO models

²Optional on all models

Waveform analysis

Search and Mark Events

Search for edges, glitches, or pulses of specified width. Any events found matching the search criteria are marked and placed in the Event table. The search can use positive/negative slopes or both on any channels.

When an event of interest is found, other similar events can be found using “Mark All Trigger Events in Record” in the Pinpoint trigger control windows.

The Event table summarizes all found events. All events are time stamped in reference to trigger position. Users can choose to stop acquisitions when an event is found.

Waveform measurements

Automatic measurements

53, of which 8 can be displayed on-screen at any one time; measurement statistics, user-definable reference levels, measurement within gates isolating the specific occurrence within an acquisition to measure

The DPOJET Jitter and Eye Analysis application offers additional automated and advanced measurements such as jitter.

Amplitude related

Amplitude, High, Low, Maximum, Minimum, Peak-to-Peak, Mean, Cycle Mean, RMS, Cycle RMS, Positive Overshoot, Negative Overshoot

Time related

Rise Time, Fall Time, Positive Width, Negative Width, Positive Duty Cycle, Negative Duty Cycle, Period, Frequency, Delay

Combination

Area, Cycle Area, Phase, Burst Width

Histogram related

Waveform Count, Hits in Box, Peak Hits, Median, Maximum, Minimum, Peak-to-Peak, Mean (μ), Standard Deviation (sigma), μ +1sigma, μ +2sigma, μ +3sigma

Bus decoding

Parallel

Data from selected channels is grouped as a parallel, multichannel bus and displayed as a single bus value. Display can be binary, hexadecimal, or symbolic formats

I²C ¹

SCLK and SDA channels are displayed as a bus per the Inter-Integrated Circuit specification

SPI ¹

MOSI, MISO, SCLK, and SS channels are displayed as a bus per the Serial Peripheral Interface specification

CAN ²

CAN_H, CAN_L, TX, or RX channels are displayed as a bus

LIN ²

Data is displayed as a bus in accordance with the LIN Version 1 or Version 2 standards

FlexRay ²

BP, BM, TX, or RX signals are displayed as a bus

HSIC ²

Data is displayed as a bus according to the USB2.0 HSIC standard

RS-232/422/485/UART ²

Channel is displayed as a bus

USB ²

Channels are displayed as a bus per the USB specification

MIL-STD-1553B ²

Data is displayed as a bus

PCI Express ²

Gen 1, 2, or 3 data rates are automatically detected and displayed as a bus in accordance with the PCIe standard

MIPI® D-PHY ²

DSI or CSI2 channels are displayed as a bus per the MIPI standard

8b/10b Encoded ¹

Control and data characters are displayed as a bus

Waveform processing/math

Algebraic expressions

Define extensive algebraic expressions including Waveforms, Scalars, User-adjustable Variables, and Results of Parametric Measurements e.g. (Integral (CH1 ‒ Mean(CH1)) × 1.414 × VAR1)

Arithmetic

Add, Subtract, Multiply, Divide Waveforms and Scalars

Filtering function

User-definable filters. Users specify a file containing the coefficients of the filter. Several example filter files are provided

Frequency domain functions

Spectral Magnitude and Phase, Real and Imaginary Spectra

Mask function

Generates a Waveform Database pixel map from a sample waveform. Sample count can be defined

Math functions

Average, Invert, Integrate, Differentiate, Square Root, Exponential, Log 10, Log e, Abs, Ceiling, Floor, Min, Max, Sin, Cos, Tan, ASin, ACos, ATan, Sinh, Cosh, Tanh

Relational

Boolean result of comparison >, <, ≥, ≤, ==, !=

Vertical units

Magnitude: Linear, dB, dBm Phase: Degrees, radians, group delay IRE and mV units

Window functions

Rectangular, Hamming, Hanning, Kaiser-Bessel, Blackman-Harris, Gaussian, Flattop2, Tek Exponential

Customized Functions using Math Plug-in Interface

An interface is provided to allow users to create their own custom math functions in MATLAB or Visual Studio

Display system

Color palettes

Normal, Green, Gray, Temperature, Spectral, and User-defined

Format

YT, XY, XYZ

Display resolution

1024 horizontal × 768 vertical pixels (XGA)

Display type

307.3 mm (12.1 in.) liquid-crystal active-matrix color display

Horizontal divisions

10

Vertical divisions

10

Waveform styles

Vectors, Dots, Variable Persistence, Infinite Persistence

Computer system and peripherals

Operating system

Microsoft Windows 10 Enterprise IoT Edition

CPU

Intel i7-2600 processor, quad core, 3.4 GHz

System memory

8 GB (16 GB on DX models)

Solid state drive

Removable, 512 GB capacity

CD/DVD drive

Front-panel CD-R/W, DVD-R drive

Mouse

Optical wheel mouse, USB interface

Keyboard

USB interface

Input/Output ports

Auxiliary input

Front panel. See trigger specifications

Auxiliary output

Rear panel. BNC connector, 0 to 3 V; default output is A-Event Trigger low true

Probe calibration output

Front panel. BNC connector, ±10 V DC for DC probe calibration (signal available only during probe calibration)

Fast edge output

Front panel. SMA connector provides fast edge signal. 1 kHz ±20%; 810 mV (base to top) ±20% into ≥10 kΩ load; 440 mV ±20% into a 50 Ω load

Recovered clock output

Front panel. SMA connector, ≤1.25 Gb/s, Output swing ≥130 mV_p-p into 50 Ω at 1.25 Gb/s. Requires Option ST6G or Option MTH to enable on DPO70000 Series, standard on MSO70000 Series

Recovered data output

Front panel. SMA connector, ≤1.25 Gb/s, Output swing of 1010 repeating pattern 200 mV into 50 Ω at 1.25 Gb/s. Requires Option ST6G or Option MTH to enable on DPO70000 Series, standard on MSO70000 Series

USB interface

Front panel: Two USB 2.0 ports on 23, 25, and 33 GHz models, one on all others. Allows connection of USB keyboard, mouse, or storage device

Rear panel: Four USB ports, two are USB 3.0. Allows connection of USB keyboard, mouse, or storage devices

LXI web interface (LAN eXtensions for instrumentation)

Class: LXI Class C

Version: 1.3

Audio input/output

Rear panel. Miniature phone jacks for stereo microphone input and stereo line output

External time base reference in

Rear panel. BNC connector; allows time base system to phase lock to external 10/100 MHz reference. Optimized (by using a software switch) for either a highly stable clock or tracking mode

GPIB interface

Rear panel. IEEE 488.2 standard

Keyboard port

Rear panel. PS/2 compatible

LAN port

Rear panel. RJ-45 connector, supports 10BASE-T, 100BASE-T, and 1000BASE-T

Mouse port

Rear panel. PS/2 compatible

eSATA port

Rear panel. External SATA interface for eSATA storage devices

Power

100 to 240 V_RMS, ±10%, 50/60 Hz; 115 V_RMS ±10%, <870 W, 400 Hz; CAT II, <1100 VA typical

Video out port

Connect to show the oscilloscope display, including live waveforms on an external monitor or projector. The primary Windows^®desktop can also be displayed on an external monitor using these ports.

Alternatively, the ports can be configured to show the secondary Windows^®desktop (also called extended desktop or dual-monitor display)

Both VGA and DVI-D connectors.

Serial port

Rear panel. Two DB-9 COM1 ports

Time base reference out

BNC connector; provides TTL-compatible output of internal 10 MHz reference oscillator

Physical characteristics

Dimensions

	mm	in.
Height	298	11.74
Width	451	17.75
Depth	489.97	19.29

Rackmount dimensions

	mm	in.
Height	311	12.25
Width	480.1	18.9
Depth (from rack mounting ear to back of instrument)	546.1	21.5

Weight

	kg	lb.
Net	24	53
Shipping	34	67

Rackmount weight

	kg	lb.
Net	22	59
Kit	2.7	6

Cooling – Required clearance

	mm	in.
Top	0	0
Bottom	0	0
Left Side	76	3
Right Side	76	3
Front	0	0
Rear	0	0

Environmental

Temperature

Operating

5 °C to +45 °C

Nonoperating

–20 °C to +60 °C

Humidity

Operating

8% to 80% relative humidity (RH) at up to 32 °C

Above +32 °C up to +45 °C; as limited by a 29.4 °C wet bulb temperature

Nonoperating

5% to 95% relative humidity (RH)

Above +32 °C up to +60 °C; as limited by a 29.4 °C wet bulb temperature

Altitude

Operating

3,000 m (9,843 ft.)

Nonoperating

12,000 m (39,370 ft.)

Regulatory

Electromagnetic compatibility

2004/108/EC; EN 61326-2-1:2006

Certifications

UL 61010-1, CSA 61010-1-04, LVD 2006/95/EC, EN61010-1, IEC 61010-1